Zone Number - Enter 2-digit zone number of the first transmitter to have its serial number entered.

Ation Ademco Lynxr En Install The Rechargeable

Introduction This Quick Start Guide can help you install the rechargeable LYNXR-I quickly and easily by providing the basic steps for installation using the built-in defaults.

For more detailed information and important notes, refer to the LYNXR-I Installation and Setup Guide.

The following steps assume that one of the system s default tables will be used.

Ation Ademco Lynxr En Serial Numbers 83 Enhanced

Default Table Summary Zone Table 1 Table 2 Table 3 Table 4 2 front door front door front door front door 3 back door back door back door back door 4 window garage door window window 5 motion detector motion detector window window smoke detector window window window window motion detector motion detector smoke detector smoke detector 26 loop 3 arm away loop 3 arm away loop 3 arm away loop 3 arm away 27 loop 2 disarm loop 2 disarm loop 2 disarm loop 2 disarm 28 loop 4 arm stay loop 4 arm stay loop 4 close device loop 4 close device 29 loop 1 no alarm response loop 1 no alarm response loop 1 no alarm response loop 1 no alarm response 30 loop 3 arm away loop 3 arm away loop 3 arm away loop 3 arm away 31 loop 2 disarm loop 2 disarm loop 2 disarm loop 2 disarm 32 loop 4 arm stay loop 4 arm stay loop 4 close device loop 4 close device 33 loop 1 no alarm response loop 1 no alarm response loop 1 no alarm response loop 1 no alarm response 92 duress duress duress duress 99 silent alarm audible alarm silent alarm silent alarm Master User Code Installer Code Duress Code Entering Expert Program Mode: installer code Interactive Mode Used to Program 56 Enhanced Zone Programming Zone characteristics, report codes, and serial numbers 83 Enhanced Sequential Mode 5800 Series transmitter serial numbers 84 Assign Zone Voice Descriptors Voice descriptors for each zone Exiting Program Mode: 98 inhibits re-entry into the Programming mode using the Installer Code.

Program mode using Installer Code NOTES: Table 4 supports the automatic paging feature (openclose events reported to pager phone number),and a Powerline Carrier Device programmed as device 8, which closes and stays closed upon burglary alarms and restores after bell timeout.

For other applications or actions (e.g., using a pulsing siren), see the 80 Device Programming Menu Mode section of the Installation Instructions.

Primary and secondary report format for all tables is Ademco s Contact ID reporting.

Tables 1, 3 and 4 record only alarms, alarm restores, troubles, and trouble restores in the event log.

Separate the front assembly from the back plate and disconnect the cable from the front assembly board.

Note: Disconnect the cable only from the front assembly board, not from the terminal block PC board.

Mount the back plate.

Make wiring connections as follows: a.

Connect the incoming phone line to either the 8-position jack or terminals 2 (TIP) and 3 (RING).

Connect the handset phone lines to either the RJ11 jack or terminals 4 (TIP) and 5 (RING).

Note: For full line seize operation, see the installation instructions.

If used, connect a piezo sounder to terminals 10 () and 11 ( ).

If used, connect a bell to terminals 11 ( ) and 12 ().

If using Powerline Carrier Devices, connect comdatasync lines from the K10145X10 transformer to terminals 9, 13, and 14 respectively.

Note: Install Powerline Carrier Devices according to their instructions.

Connect wires from the K10145X10 (K101450CN) AC Transformer to terminals 15 and Make battery connections as follows: a.

Remove battery retainer.

Remove backing from tape on back plate.

Insert battery pack into back plate.

Install battery retainer.

Connect battery connector to receptacle on terminal block PC board.

After all wiring connections have been made, snap the front assembly to the back plate so it is held by the locking tabs.

Plug the transformer into a 24-hour, 110VAC unswitched outlet.

Note: Rechargeable batteries may take up to 48-hours to fully charge.

LOW BAT message should clear within four hours, or by entering Test Mode.

FUTURE USE GND SOUNDERS PLCD AC RJ11 8 POS JACK WARNING: TO PREVENT RISK OF SHOCK DISCONNECT TELEPHONE LINE AT TELECOM JACK BEFORE SERVICING THIS UNIT TIP RING TIP RING ( ) ( ) () ( ) () DATA IN GND DATA OUT DATA SYNC OUT IN POWERLINE CARRIER DEVICES INTERNAL 7845i-L MODULE ONLY STANDARDHIGH CAPACITY BATTERY CONNECTOR SUPER HIGH CAPACITY BATTERY CONNECTOR ALARMNET LRRIP COMMUNICATIONS PORT LOCAL SOUNDER DISABLE SHUNT REMOVE TO DISABLE THE LYNXR-I CONTROL IS COMPATIBLE WITH THE FOLLOWING INTEGRAL RECHARGEABLE BATTERY PACKS: PN LYNXRCHKIT-SC PN LYNXRCHKIT-HC PN LYNXRCHKIT-SHA REPLACE EVERY FOUR YEARS WHEN AVAILBLE INCOMING TELEPHONE LINE EARTH GROUND PREMISES TELEPHONE WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM FUTURE USE PIEZO BELL 6-14VDC 30mA max.

VDC 120mA max. (e.g.

WAVE2EX) NOTE USE ONLY THE K10145X10 OR K10145CN TRANSFORMERS PROVIDED LYNXR-I WIRING CONNECTIONS K10145X10 PLUG-IN TRANSFORMER 9VAC, 25VA AC AC SYNC COM DATA X10 ONLY CONNECTIONS V1 System Programming Step Action 1.

Press 97, then press a number 1-4 to select a default table from the tables listed on page Program the variable data fields as follows: a.

RF House ID - Press 24, then enter the desired 2-digit RF House ID for wireless keypads.

PABX Access Code (if used) - Press 40, then enter up to 6 digits.

If fewer than 6 digits are used, press to end the field and advance to the next field.

Primary Phone Number - Press 41, then enter the primary phone number, up to 20 digits.

If fewer than 20 digits are used, press to end the field and advance to the next field.

Secondary Phone Number (if used ) - Press 42, then enter the secondary phone number, up to 24 digits.

If fewer than 24 digits are used, press to end the field and advance to the next field.

Secondary Account Number (if used) - Press 44, then enter the secondary account number.

If only 3 digits are used, press to end the field and advance to the next field.

Primary Account Number (if used) - Press 43, then enter the primary account number.

Pager Characters - Press 88 if using Default Table 4, then enter up to 16 digits which may be required by your pager service (e.g.

PIN, etc.). If fewer than 16 digits are used, press to end the field and advance to the next field.

Download Phone Number - Press 94, then enter the downloading computer phone number, up to 20 digits.

Installation Manual Ademco Lynxr En